This page should describe Verification and Unit Tests performed for this stand alone feature and should provide links to all the result pages.
| Table of Contents |
|---|
Summary
The E3SM Developers test suite was used to make unit testing without PHS on compy in /compyfs/d3m045/e3sm_scratch/. All passed.
Unit Testing
Unit Testing: short-desciption-of-testing-here
Date last modified:
Contributors: Yilin Fang
Provenance: (Run provenance Link, Code Tag, etc:)
Results: (link to results, data and plots)
Point case model setup was from Kennedy et al. (2019) under the ambient condition. Model parameters in Table 1 of Kennedy et al. (2019). Model results were compared using ve
- Spinup results without PHS on compy in /compyfs/d3m045/land_runs_verification/v1.ICLM45.compy.intel.Ca54ad57/run
- Spinup results with PHS on compy in /compyfs/d3m045/land_runs_verification/v1.ICLM45.compy.intel.Ca54ad57/run_phs
- Post spinup results without PHS on compy in /compyfs/d3m045/land_runs_ver_rst/v1.ICLM45.compy.intel.Ca54ad57/run
- Post spinup results with PHS on compy in /compyfs/d3m045/land_runs_ver_rst/v1.ICLM45.compy.intel.Ca54ad57/run_phs
Plant water stress factor was calculated using soil moisture stress (SMS) parameterization before plant hydraulics stress (PHS) scheme was implemented.
Volumetric soil water content at 50 cm depth without PHS (middle panelwith soil moisture stress (SMS) parameterization (middle column in the following table) using ELM differs from those simulated by CLM5 (Figure (a) in the right panelthird column in the following table) in Kennedy et al. The discrepancy in soil water simulation between ELM and CLM5 will result in model discrepancy when using plant hydraulic stress (PHS) in ELM. However, similar to CLM5 (Figure a,c in the third column), ELM-PHS simulates wetter soil in the dry season (Figure in the first column) compared to ELM-SMS (Figure in the second column).
| Soil Water Content simulated by ELM PHS | Soil Water Content simulated by ELM SMS | Soil Water Content simulated by CLM5 |
|---|---|---|
 |  |  |
The following two figure shows two figures in the table below show stress factor (BTRAN) comparison with (leftsecond column) and without PHS (rightfirst column) in Sep, Oct and Nov of 2003. They are higher compared to the Kennedy paper (solid line in the third column in the figure on the bottomtable below). The discrepancy may be caused by the Medlyn photosynthesis model and soil water calculation in CLM5.
| BTRAN simulated by ELM SMS | BTRAN simulated by ELM PHS | BTRAN simulated by CLM5 |
|---|---|---|
 |  |  |
As the soil moisture simulations don't match between the models, the match between ELM and CLM5 in terms of plant organ water potentials is not expected. However, similar to CLM5 simulation (Figure (a) in the bottom right panel), root water potential is higher than the others and there is almost no discrepancy among stem, leaves (top figure below)..
| Plant water potential simulated by ELM PHS | Plant water potential simulated by CLM5 |
|---|---|
 |  |
Verification Test 1
Verification Test 1: short-desciption-of-testing-here
Date last modified:
Contributors: Yilin Fang
Some functions such as PLC (vulnerability curve) were verified using excel.
Provenance: (Run provenance Link, Code Tag, etc.)
Results:
...
The complete package passed the E3SM Developer's Test Suite.
Point simulations were compared to results with plant hydraulics turned off as well as those from Kennedy et al. paper. Model produce reasonable results.